Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
Actually i want to transfer my data using 10G Ethernet connection. Xilinx offer variety of cores for 10G. There are some that state they are MAC and some that state the core has just PCS/PMA. What do i actually need to transfer my data from FPGA to another card, using 10G Ethernet connection?
Hello,
I need guidance on using SFP port on ML605. I am unclear which IP core to use with it. There are a number of 1G and 10G cores available which confuses me. There are cores which state that they are MAC controllers, while some say they implement the PCS/PMA . which one do i exactly need?
Hi,
I am using A3P1000 FPGA. Somehow its pin number 1 got damaged. As I can see from the data sheet that this pin is a grounding pin of bank number 3. On the same bank, pin 17,25,1,29 and 41 are also ground. Can I leave that broken pin unconnected and sold the FPGA on my card? will it degrade...
yes i saw the tutorial.. every thig is fine when i take the picture as a whole.. but when i take in chunks it gives problem
---------- Post added at 20:42 ---------- Previous post was at 20:40 ----------
is there any one who have taken picture from this camera in chunks??
PLEASE HELP ME OUT ASAP!!!!
ITS REALLY URGENT!
i am using this cam.. everything works perfectly fine when i read the image in one go.. the problem arrives when i start to read its image in chunks. i get FFD9 twice or thrice, and the data is corrupted. Please suggest me the solution, what am i...
hello.
I am trying to program my PIC18F4550 to work with external 20Mhz Oscillator. I have tried each and every single command i came across the reference manual for PIC-C programming language, but i am not successful to accomplish my task. Here's my code,
#include<18f4550.h>
#use delay...
Hello,
I am doing a project, in which i have to interface a serial camera with PIC18f4550, and in order to store that image i am using 62256 RAM. My problem is that i don't have any circuit diagram to proceed. Can any one please provide me with a circuit diagram explaining how to interface the...
can u tell me how to make a simple test to use GPRS on sim300? i mean can u give me the sequence of commands u entered to use GPRS on hyperterminal? i think my device's GPRS is not working properly, so i need help.
yes i used at+cgsms=? command and it returns +CGSMS: (0-3) . I think my modem's GPRS is nor working properly, can you please tell me how to make a simple test to check if GPRS is working properly or not?
i m getting the same error.. actually i am trying to send SMS over GPRS link. following is the command sequence i am following.
AT+CGATT=1
AT+CGSMS=0
AT+CMGS="number"
>message ctrl z
+CMS ERROR 515
CMGS is working fine with when at+CGSMS=1 and 3
i thought there is some problem with gprs, but...
hay, i am using sim300 and i am also getting the same error. actually i am trying to send sms with gprs link. following is the command sequence i am following.
AT+AGATT=1
AT+CGSMS=0
after this i wait for a while and then send the sms sending command.
AT+CMGS="mob num"
>message then ctrl z...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
