Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
Hi guys am back,I had to change my PIC16 to PIC18 which have two serial port, one port I will use for gsm and another one for gps, but problem I have now, I have tested my gps with PC and everything worked fine, so far what I want is to display the latitude and longitude on the LCD but am not...
Thank you a lot, I had problem with my LCD display spend 2 days changing your code and bmb_10 code playing around to find out what is the problem and why is not working and yesterday I found my LCD display it was not working, so thank you a lot and I have change back to 4 bit mode and 8 bit...
Hi I have tried both ways but not is display so I don't know what to do now, I have tried to connect pin RW to ground still the same problem any idea what I should do? I lok the code in my drivers for LCD.c which is
//////////////////////////////////////////////////////////////////////////////...
Hi bmb_10 thank you, yes I wanted because of the Schematic that's all, also another question I have LCD and I have connected everything, when I connect pickit2 I can see one line with block box but nothing is displaying, so I don't what I have done wrong,
LCD
PIN 1 --> Ground
PIN 2...
Thank you Hemnath, I have tried to check proteus PIC16F877A I can't find pin 11, 32 and 12, 32 what should I do??
- - - Updated - - -
Thank you bmp_10, yes I will get that book as well and it will me..... because I have a lot to do with GSM and GPS as well, but I will ask more questions...
Hi am back again, and that book you recommended me to use it helps a lot, thank you again, Also I wanted to create Schematic diagram but I can't use Multisim because I cant find PIC16F877A, Also I have tried to use ExpressSCH but still I cant find all component am looking, so which software can...
Hi bmb_10 and hemnath ,
Thank you guys for your help,I have tested the code with LED and worked fine without any problem thank you a lot...Actual I will be around to ask more question if I have on this thread...
Hi bmp_10
Thank you for your help appreciate, also I will do testing tomorrow then I will give you feedback as soon as possible, also I have got that book already...Again thank you, if I have anything I will keep posting on this thread.....
Hi bmb_10
Thank you for your help, I have tried to compile the code and worked fine, in CCS C compiler and even in MPLAB, so my question is that because I have already build PIC16F877A in veroboard with 20 Crystal osc so on that code can change to 20 MHz instead of 4 MHz??
Thank you for your help, yes I have already downloaded "MPLAB®IDE Plug-in", and also I have tried to compile the code but am getting error so any solution I will appreciate, or the problem is my CCS C compiler the way I installed??
- - - Updated - - -
My MPLAB is version 8.63, also I have...
Thank you for your help bro, Actual am mistaken my self,what I was planning to say is am using MPLAB with Pickit 2, also with my project am using PIC16F877A so for MPLAB I have to use CCS C language and not compiler, I need your help please if possible. I have never use CCS C compiler before...
Hi guys am doing this project Vehicle security system with theft control and Accident Notification so before I start anything I want to test my PIC16F877A if is going to work with CCS C, so I want to test my 2 LED blinking I have found program online which will work but is not working at all...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
