Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
good morning dears
need for emergency help !!!!!
I want to reach out an impedance matching between microstrip line (characterisitc imedance Zo) and rectangular waveguide ,actually is a SIW,
through a microstrip step discontinuity transition with characterisitc imedance Z1, (see the attached...
thank you for your reply
actually I need to know input impedance at resonant frequency to use it later in another impedance matching procedure but, it's possible to deduct input impedance from S-parameter ?
good evening my dear
I am designing a microwave network in HFSS which I need to know the input impedance of a substrat integrated waveguide and because Zin = Z11 when I2 = 0 (open port), I have placed a LumpedRLC in port 2 by choosing R = 50 GOhms, in fact I had some result that I am not sure if...
Good morning Guys
I have to write a matlab code in order to find effective refractive index of a slab waveguide (metal-substrat-metal),
can any one give some refrences or formula ?
thank you very much
hi how are you
I have a microwave complexe geometry or I find it complexe, a parallalpepide with several holes inside it, well I must analyse it using matlab, my problem is How to build such geometry using matlab, I read that a complexe geometry should create in approporiete software (Adobe...
Hi beautiful minds
I have to analyse a rectangular waveguide working an X-band (8-12 GHz), this time using FDFD, I had wrote a matlab code necessaire for this reason (see the attached file), well, the code works very well, unfortunatily the cut-off frequency not in the same value like in theory...
Hello and thank you very much for answering me, in fact, I'm blocked for a long time in this problem, it's about analyze a Substrat Integrated Waveguide with the Boundary Integral Resonant Mode expansion method where I have to find coefficients Aij, Bij, Cij and Wm (in attached papers you can...
Hello,
Please, in the matlab command window How to solve the Helmoltz equation in the 2D space domain, in fact, I have to find proper functions and proper modes in an irregular geometry formed from a rectangle With two holes in the interior where the radius of holes and the width of the...
Hello my dears,
it's possible to export the solution in pdetoolbox (i.e current density, calculated voltage) to the command window. and please if you hzve any pde exemples or tutorial don't hesitate to send it to me. thank you
Hello, you might want to see (and try to redo) this paper, is very important, you will find the answars of your questions ,, Good luck
(paper title : Improvement for the design equations for tapered Microstrip-to-Substrate Integrated Waveguide transitions )...
Hello friends, please is there anyone can give me the best HFSS configuration (substrate error, driver thickness, etc.) in order to find simulation results close to the measured results ... thank you very much
Hello, thank you very much for answering me, unfortunately the problem always present; very bad Sparameters (S11>-10dB). According to my knowledge the probe must ensure the continuity between the two microstrip lines then the S-parameters must be similar to a single microstrip (at least behaves...
I'm trying to simulate the structure in the attached file, unfortunately the results obtained are not the desired results. In fact, the structure is composed of three sections of a 50 ohm microstrip line, where the probes ensure the contact between them (see the figure). The distribution of the...
Hi dears
I would like to know if it's possible to change automatically substrate permittivity in HFSS. let's say I want to use diffrents materials for the same HFSS drawing and I want to let HFSS picks one material among a set of materials already selected. I'm a bit confused, can anyone help...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
