Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Recent content by majnoon

  1. M

    Intertool Communication for Cadence Allegro

    Is in input. When you place mouse on any options it will display what each of them do. M
  2. M

    Intertool Communication for Cadence Allegro

    You can do this by going to Setup>>User Preference Regarding selection in schematic try to start Capture first then Allegro or vice versa There is a little glitch that persist sometimes. Good Luck, M
  3. M

    Defining components height in Allegro PCB Designer

    Congratulations on building your own footprints rather than relying on some unverified tool to do it for you. Now to your question, after you have defined component outline go to setup--> areas --> Package Height. Use control menu to enter value for height Good Luck, M
  4. M

    CONVERTION OF .DXF TO .MAX

    Make sure that units in OrCAD is the same as autocad. M
  5. M

    surpantine route in PADS like delay tune in allegro

    Re: surpantine route It is not as easy as Allegro but you can do it. Go to your settings and use Blaze Router. M
  6. M

    Generic two terminal SMT footprints (0402, 0603, 0805, etc.)

    Re: Generic two terminal SMT footprints (0402, 0603, 0805, e It gives you a unique perspective into designer's world. You will be one of few EE that is best to work with. I always have great working relation with EE who have done some board lay out, their guidance and instructions make doing a...
  7. M

    Generic two terminal SMT footprints (0402, 0603, 0805, etc.)

    Re: Generic two terminal SMT footprints (0402, 0603, 0805, e You said it... as an engineer you gave in to a "footprint maker" and end up with so many different names and craps. A full time designer build a working and lean library. M
  8. M

    Generic two terminal SMT footprints (0402, 0603, 0805, etc.)

    Re: Generic two terminal SMT footprints (0402, 0603, 0805, e After IPC dumped its role in releasing its standards to a private company which uses personal liking of few , we have seen issues with some of their footprints. Footprint making is fundamental to design if one can not make a proper...
  9. M

    Generic two terminal SMT footprints (0402, 0603, 0805, etc.)

    Re: Generic two terminal SMT footprints (0402, 0603, 0805, e It all depends who is assembly your board. Personally I never use footprints provided by layout tools nor I use PCB Matrix. We have our own footprint library with define parameters all verified and approved assembly team. M
  10. M

    Best General Purpose Schematic Program?

    Also if you are getting PADS depending on your license you can get PADS logic which is native schematic for PADS. This way you can use cross probe I personally like OrCAD better. Regarding connection to Digikey parts if you are doing only test boards or even home made designs that should be...
  11. M

    Best General Purpose Schematic Program?

    I usually do not reply to best "program" questions. But CIS you are trying is very versatile tool. Other options are mostly tied to specific layout tool. There is also View Logic now called DX Designer after Mentor took it over. It has many features of CIS OrCAD. M
  12. M

    Required IPC STANDARD (help me pls....)

    Please read above post which says you can buy it from IPC site. What is it to upload?? M
  13. M

    Generating Silkscreen in PCB Editor

    First turn on silk layer and do clean up. If you want to clip silk lines or move ref des then use Auto silk otherwise your fab house will do it. Then map your silk layer in artwork dialog box to generate Gerbers. M
  14. M

    SDRAM timing budget calculation

    Best is to see Manufacturer Data Sheet. Each Manufacturer specify this for their devices. M
  15. M

    Help me with component rotation in Allegro

    Re: rotation in allegro As I have mentioned before regarding Allegro, make sure you work with Control Menu. Has nothing to do being unfriendly is all there look again! M

Part and Inventory Search

Back
Top