Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Recent content by lord_of_destruction

  1. lord_of_destruction

    Is there a software to simulate radar systems?

    RADAR simulator can you PLS upload it because it needs time and they may refuse your request also
  2. lord_of_destruction

    How to download the CAEME EM CD?

    REQ:CAEME Hi all, Can anyone PLS tell me how to download the CAEME EM CD? Kindest regards,
  3. lord_of_destruction

    What is the function of the waveguide flanges?

    Can anyone PLS tell me what is the function of the waveguide flanges?
  4. lord_of_destruction

    Infrared Remote Control

    can anybody tell me Pls the relation between IR and heat?
  5. lord_of_destruction

    How to connect 3510i to PC?

    REQ:Nokia 3510i Hi all, does anybody know how to connect 3510i to PC? best regards,
  6. lord_of_destruction

    Question about the waves sinusoidalis

    waves sinusoidalis Sine waves are used because in liner circuits the effect on them can be only phase variation and hence the signal isn't distorted regarding system response sine waves are not optimal for that but delta function is
  7. lord_of_destruction

    The difference between cordless and cellular phones

    cordless and cellular? Compy The GSM is the standard used in Europe for Cellular(mobile) communication and it uses the TDMA and FDMA techonolgies for making calls CDMA is the equivalent system for GSM but in North America however this system works in a different way using what is called...
  8. lord_of_destruction

    Why we use MOS family if BJT has better GAIN or BW?

    Re: Why we use MOS family? sorry but i guess bjt is a majority carrier device as NPN carriers are electrons while mos is minor carrier since we make a channel opposite to kind of used SC like n-channel
  9. lord_of_destruction

    Why we use MOS family if BJT has better GAIN or BW?

    Re: Why we use MOS family? Bjt is better than mos in both gain and BW it's also faster but the mos advances bjt in it's very high input impedance due to the use of oxide it's easy fabrication and easy scaling technology that makes its speed very high and near to bjt lower cost low power...
  10. lord_of_destruction

    What things should a junior RF engineer learn ??

    u should know some basics like RF amplifier design Some Famous ICs like 1496 & 3028 and their apps in RF PLL
  11. lord_of_destruction

    Help me design class c amplifier at 5MHz

    Re: class c class c is a common emitter amplifier works in off region and needs only ac signal to let it operate on/off and according to application needed it's usually used in AM
  12. lord_of_destruction

    Help me build an ADSL line network

    Re: Build network help however using coaxial is bad choice since it's speed is very low compared to cat 5 also it's not assured about it performance or easy to connect
  13. lord_of_destruction

    Designing an amplipier

    designing amplifiers depend mainly on some assumptions where for a Common emitter as an example u can assume that current in universal divider = 10 and 11 * (base current) and Volt on emitter resistance = 0.1 Vcc and Vce = 0.5 Vcc but these assumptions mainly depend on the number of unknowns u...
  14. lord_of_destruction

    What are the best softwares for analog RF design ?

    Re: Analog RF design all what i can say try 2 use Pscpice 10 or better ADS they are great in simulation and design actualy i think they r the best
  15. lord_of_destruction

    Help me with designing a PCM

    Re: PCM u need to know what is PCM (pulse coded modulation) or u need a circuit for it's operation

Part and Inventory Search

Back
Top