Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
Re: cc2500 and 8051
hi
thx microlab i think iam so close ... iwill try it then i will told you the result ... unfortantly i got exams so i will try it after three weeks .....
but at the last can i ask you question
what is the function of the pins GDO0 GDO2 its confusing in datasheet...
Re: cc2500 and 8051
hi
thx alot microlab this is so close .... the last thing ... how can i configure the module
i.e what pins and sequence i will use to make module in configuration mode
thx for your help ...... now i think i can use the module easily ..... just the configuration still...
Re: cc2500 and 8051
hi
thank you microlab i got it till now ... the last thig.. can you summarize in steps how can i initialize the module
i know i am like a a pain but this my graduation project and this is the last step on it
thx
Best Regards
Re: cc2500 and 8051
hi
no , i want to one thing before even try it .... should i use it with its default configuration ... and just to put data in spi MOSI it will work
thx
Best Regards
Re: cc2500 and 8051
hi
thx microlab
but can you told me steps i can program it to mcu to configure the cc2500
iam using smartrf sudio , i get initial configuration iam connecting
PB6/MISO ->SO
PB5/MOSI ->SI
PB7/SCLK ->SCK
PB4/SS ->Csn
PB2/AIN0-> GDO0
PB3/AIN1-> GDO2
how i can...
Re: cc2500 and 8051
hi
First of all i want to say thank you microlab
i am using atmega16l with interface spi to cc2500 mounted in QFM-TRX1-24G
module with 6 active pins + vcc , gnd ,
SO SI SCK Csn GDO0 GDO2 connected to the microcontroller iam trying to send low traffic data with any...
Re: cc2500 and 8051
hi
i just want to make sure of one thing when iam using cc2500 if i send data in the spi with the default configuration would it transmit it and i can receive it normally ...
and if that .... how can i interrupt the MCU about data reception
Best Regards
hi
iam working in aproject with wireless sensor network
iam using the nodes to monitor an industrial process
i got to use 6-10 nodes
my part in the project is to make the network between nodes
all the protocols i know was used in large number of nodes
so if any one can advice me what...
signaling module(dial .ringing.,back ringing)
hi all
i got this task today and i have to solve it within two days i really need any help
the task :
Design and implement a telephone signaling module that generates standard signaling tones ( dial, ringing, ringing back, busy tone).that is...
hi
i have a question
i will do my graduation project next year and i am so interested in digital communication & gsm and planning for the last
i seek knowledge to have a creative idea to make a good project for colloge and for my career so if any one could tell about the problems in the...
hi all
iam new in microcontroller design i need to make asimple project using z80 microcontroller in my college i need to make aclk generator for it so i need some advice about any good ic and its suitable frecuency and what it contain from electronical components .
thx
possible questions on white led
thank you for help
now i will try to get the information i need
Added after 1 hours 2 minutes:
I still have trouble on searching over the internet so i think if any one can give me link to any reference in this field i think i can have the information i want...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
