Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
Dear Sparrow,
Thanks for you reply.
i am using TCEBB1C Finger Print Module.
I have basically two issues.
1) i dont know how do i make connection with my microcontroller to start communication.
2) From where do i start my coding and how?
So if you have any schematic diagram regarding this...
Dear,
i have to interface UPEK finger print module with ARM microcontroller.
i have used some other Fingerprint module with it, but new in this finger print module.
i dont have any idea, what to do?
can anybody help me how do i start and which command should i use for the same?
Thanks in...
Re: sd card doubt
Okay fine..
if it is then i can try on PIC Micro controller...
for that i need that software, right??
so please give me the full version crack link... okay..
Re: sd card doubt
that is okay..
but i want to interface it with the same MCU p89v51rd2 from philips.
actually the link for the MicroC full version with crack which u have mentioned on earlier post but i cant understand the link properly...
can u send me the same link on my personal id...
Re: sd card doubt
Yes it has 1kB of RAM..
But i cant find n e solution for the same controller.
So if u have n e solutions then give me the code if u have.
Thanks in advance...
sd card doubt
Hey can you please tell me that Can i interface sd/mmc card with Philips P89v51rd2 controller.?
Actually it has a SPI facility and also having a 64KB of flash. so i need to know that if it is possible with PIC and AVR controller, then will it possible with this P89v51rd2??
Hello GSM man..
i am waiting for your reply.. i need to get it as soon as possible.
as i told u that i cant do anything after starting the TLS connection.
it will automatically CLOSED by the server side.
and i also dont know how to send the AT commands for the authentication..
i mean to say...
i am able to start the TLS feature by writing STARTTLS command,
but now the problem is with MAIL FROM command.
i mean to say when i write the command, MAIL FROM:jagrut911@gmail.com
it will reply CLOSE immediately...
so what should i do now for establishment of the connection..
please reply...
hey i am just near to reach to establish the connection..
when i configure smtp for the gmail, it will response me by telling like,
+IPD64:530 5.7.0 Must issue a STARTTLS command first. 5sm314910yxg.46
and when i configure smtp for the yahoo, it will give like,
+IPD97:530 authentication...
Thanks for your kind support...
Now i am able to get the response from the server side, but when i send the commands to the server it will response me like,
>> at+cipstart="tcp","smtp.gmail.com","25"
<< OK
<< CONNECT OK
<< +IPD42:220 mx.google.com ESMTP 8sm2041661yxg.60
>> at+cipsend
>> >...
I had tried so many times..
by the way if i am pressing ENTER key, then it means that <CR><LF> both included in it..?? Right???
Till now i am pressing an ENTER key only. I it fair enough to press an ENTER key or should i have to do some another logic.?
Ok fine..
Here i am sending the code which i have written in my Teminal window.
The same phenomena which u considered in your code like,
>> is data I send to the SIM300
<< is data it returns to me.
************
>> at
<< OK
>> at+cmgf=1
<< OK
>> at+cops?
<< +COPS: 0,0,"AirTel"
<< OK
>>...
okay i understand which smtp server name should i have to use..
in my case i am using gmail's and yahoo's smtp server name like smtp.gmail.com and smtp.mail.yahoo.com respectively with port number is 25.
But as u mentioned in the above thread that the response came from the server side with...
Hey GSM man.. thanks for ur reply..
i have tried but i m still bit confused regarding the name of the smtp server..
is it necessary to keep the smtp server name is of our company's smtp which has allocated to the company's outlook express..???
if i wish to mail from the gmail and to recieve...
I have done what u have mentioned in this thread before, but the problem is with after the AT+CIPSEND.
What i mean to say is that once i send the command like,
AT+CIPSTART="TCP","smtp.mail.com","25"
it will respond like, OK ... and then CONNECT OK...
and replyh from the server is like...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
