Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by ITP

  1. I

    Suggest an RF source with 81.36Mhz, 300W Output

    Hi, The RF Power source of our CO2 laser has gone bad. Unfortunatley the OEM is not suporting it and also most of the components like RF MOSFETs are obsolete. So it is dificult to repair it. So my idea is to design a new RF Power source by integrating an rf-exciter with a rf power amplifier...
  2. I

    Suggest an RF source with 81.36Mhz, 300W Output

    Hi all, I am not an expert in RF design but have a requirement of RF source for an RF-excited CO2 laser. The RF source required is of 81.36Mhz frequency with a power output of 300W. Please suggest an RF source or a practical circuit or this application. Thanks and regards Itp
  3. I

    Request for RF MOSFE BLF175

    Hi All, Can anybody know where I can purchase RF MOSFET BLF175 or its drop-in replacement part. Thanks and regards Itp
  4. I

    Substitute for Philips microcontroller S87C752-4N28

    Hi All, Any pin to pin replacement for Philips micro controller S87C752-4N28. Please suggest. Regards Itp
  5. I

    How to Interface a 16bit DAC with SPI port with HMI or any PLC

    Thanks FvM for your fast response. I have used SPI port with micro controller for interfacing DAC but not with PLC. Do you have any examples, document or links? Thanks and regards Itp
  6. I

    How to Interface a 16bit DAC with SPI port with HMI or any PLC

    Hi all, How to Interface a 16bit DAC with SPI port with HMI or with PLC. Thanks and regards Itp
  7. I

    ispLEVER Classic problem

    isplever classic Hi, I am using ispLEVER Classic Schematic editor for coding for Lattice GAL16V8D 10LP chip. I am new to this software and GAL. I have following doubts. 1. How can I edit the Constraint to change Default PIN assignments. 2. How can I do PIN locking (This means physical pins...
  8. I

    Interfacing keys to dsPIC

    Hi All, Thanks for your reply, I have developed a module on this processor to generate a pulse of following spec. Frequency : 1Hz to 100Khz ( user can vary) Duty Cycle: 10% to 90% ( user can vary) Also I have interfaced a Serial Seven segment LED display to this processor through SPI...
  9. I

    Interfacing keys to dsPIC

    dspic fun Hi all, How can I interface Four keys to PortB of dsPIC30F2020 Micro. I have some problem in configuring the port. My code is as follows. ADPCFG = 0xffff; // all PORTB = Digital TRISB = 0xffff; // port B input CNEN1 = 0x00ff; CNPU1=0x00ff; I this I am not able to...
  10. I

    Can anybody suggest a circuit of a Pulse generator ?

    Pulse generator Hi, Can any body suggest a circuit of a Pulse generator with following spec. Frequency: 0.1Hz to 100kHz Duty cycle: 10% to 90% Amplitude: 5V Regards Itp
  11. I

    Looking for materials on machine automation with HMI

    Machine Automation Hi All, I have a project on Machine automation with HMI (Human Machine interface). I am new to this field. Can any body kindly suggest any venter,links and good forums related to this. My requirement. 1 Analog Inputs (4-20 mA) 16 2 Analog Inputs (0-5 V) 16 3 Analog...
  12. I

    Microcontroller based SMPS

    smps design using microcontroller Hi All, Silicon Labs Si8250 is a "Single-Chip, SMPS Digital Controller" . Anybody have used this uC? Thanks and regards Itp Link: https://www.silabs.com/tgwWebApp/public/web_content/products/Digital_Power/Digital_Power/en/Si8250.htm
  13. I

    This is a working RS232.... ICD2 !!!!

    Hi Make_Pic, Thanks for the reply. I am programming from the Debugger menu. Any other possible resons. Regards Itp
  14. I

    This is a working RS232.... ICD2 !!!!

    I made the ICD2 version from h**p://www.stolz.de.be/. But it shows this error message. My target is PIC16F876 What could be the problem. Kindly help. Thanks and regards Itp -------------------------------------------------- MPLAB ICD 2 Ready Connecting to MPLAB ICD 2 ...Connected Setting Vdd...
  15. I

    some sample question papers for campus interviews

    l & t valdel campus interviews This may be helpfull. Regrads Itp Courtesy: projectw
See more

Part and Inventory Search

Back
Top