Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
Hello,
I have units that requires frequent series knob rotation (volume) & push button with more precision, can anyone advise should i go with Robotic ARM or any suitable servo motor.
Also kindly help with any references to start with both Robotic & Servo.
Thanks
Hussain
Hello
I have circuit cards that is not functional, I would like to troubleshoot and understand root cause, like which circuity or IC chip is causing the failure.
the circuit card consist of XLINX, DSP, FPGA IC's,
Any advise or software that can help me to start with? other than JTAG,
Hello
I am planning to replace electrical switch with programmable relay switch, its purpose is to turn on/off, that powers to step down converters 3.3, 15,-15,5 Volts
rating would be 50V DC 10A,
Any suggestion, which i can start with
Hello, I have refreshed my PC and there are no drivers below is the one i am unable to get
intel (r) 6300esb lpc interface controller 25a1 driver
Any help greatly appreciated
First question - can i install DOS & XP on PC? I am not sure how this can be done, do you mind sharing me some link to proceed?
this is the experiment i am trying , I have found one PC, which has 2 COM ports.
Hello,
I have 2 PC's, 1 for DOS and 1 for XP, both are used for bench programming and they are communicated using serial port, now I would like to use single PC, which can handle DOS & XP and there communication
1) How can make internal communication between DOS & XP ?
Hello
I have customized board with some application Bios & Operating system in it. but now i am trying to get back to factory setting BIOS (advised by manufacturer), But when ever i try to load Factory BIOS , I am seeing this "ERROR : can't analyze the IIM information"
I am trying to...
Hello,
No, I cant enter in BIOS setup neither F11, F8 etc nothing seems to be responding, apart from few led's on motherboard.
there was wrong bios loaded,
Hello
I have installed wrong BIOS installed in my laptop, I tried to get all the BIOS files from Manufacturer website,
since my laptop is not even trying to switch on :bang: & I am not sure how to go ahead loading correct BIOS.
my question is :
1) what ways i have to load correct bios since...
Hello All
I am measuring the signal (the signal should be less than 0.1 VDC) & the signal is read from the osciilloscope (TDS460), My question is How to sample the noise and substract the same with actuall signal?
there are Oscilloscope functions called to read required signals in Lab...
Hello All,
May i know which Best software tool (Preferably Open source ) for creating POP UP displays?
My idea for POP UP message display :
when ever there test cycle (specific time give during start up) is complete, there should be POP UP & Buzz as-well.
Any new ideas are welcome
Thanks...
Hello Klaus
Thanks for your response,
We have Earth connections and all are connected to star connection to it and other filter on Power supply end.
Actually the test station is Automated test equipment & i have 3 such kind of station .. I am facing trouble with only one Test station.
there...
Hello
Appreciate your response, the problem is we cannot use open capacitors etc we need some standard ready instruments like( Wruth electronics, etc) who provides solution for this kind of issues.
Hussain
Hello
I have one test station which has various stand alone instruments like Audio analyzer , spectrum analyzer . Oscilloscope , and other radio testing instruments .
Every time Audio test fails due to the signal interference. it would be great if any one refer me some good website for...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
