Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
Dear All,
in my research work , i found a little problem in the mathematical derivation,
i was doing modeling for a cylindrical magnetron cavity sealed at the two ends.
Now, i need to derive another equations with new boundary conditions but I'm confused in getting those B.C. and those...
Dear All,
First of all, i wish you all luck and happiness in the new year.
Now, I'm working on HFSS 10 and i need to know if their any ability to export the plotted Field inside any cavity in terms of V/m to an external file ??
I need to get the field values that HFSS simulated in order to...
Dear All,
First of all, i wish you all luck and happiness in the new year.
Now, I'm working on HFSS 10 and i need to know if their any ability to export the plotted Field inside any cavity in terms of V/m to an external file ??
I need to get the field values that HFSS simulated in...
Dear All,
Hello every one here, i hope you are doing great all.
In the attached HFSS design, im trying to calculate the resonance frequency of an 8-Slots magnetron cavity using the eigenmode technique of the HFSS10. I divided the cavity into 2 half and simulating only on half of them to...
Dear All,
I need to know which mode that the HFSS draw when i draw the Mag_E field distribution inside a cavity.
I mean , in an eigenmode problem, after calculating the modes (the resonance frequencies) , i draw the field overlay in the cavity and the drawing is okay
but i need to know...
Dear All,
Using the HFSS 10, After Running the simulation that calculates the eigenmode resonance frequencies of a magnetron cavity, it stops and gives me the following message:
[error] Recovering adaptive solution, process abc3d: Eigenvalue calculation failed to converge. (12:34 PM Feb 17...
Dear All,
In the way to finish my research, i started to validate the Matlab code results that i wrote to estimate the resonance frequencies of an 8-slots magnetron cavity with those results that HFSS (V 10.1) gave to me and i found the following problems:
1- I found a big mistake that i...
Dear All,
I really cant find the suitable words to thank you about your continuous support , that was is really very kind of you.
i found some confusing check boxes in the solution setup (under the eigenmode solution type) that i don't know if i should check them or leave them without...
hfss maximum delta frequency per pass
Dear All
first i would like to thank two of our forum members from the deepest part of my heart about their kind and helpful support, these two members are:
navhuo,
RFSimulator.
The recent problem that I'm facing right now is that i cant choose three...
Re: DF antennas
Dear Ali,
I do have some ADF antenna structures but not in a micro strip antennas, if that helps please let me know.
Tell me something, wy you are interested in ADF , are you in the avionics field? im an avionics engineer.
best regards,
Goher
e-mail: m_goher@yahoo.com
Dear All,
I'm Looking for the latest version of the HFSS , which is V. 10 , because the one that I'm using right now (V.9) is unable to solve the problem that I'm trying to simulate ( an 8-slot magnetron cavity microwave power amplifier) and the company declared that clearly in the V.10...
design of cylindrical cavity+hfss
Dear All,
First of all, i would like to thank every EDA Board member who replayed to my inquiry specially the following members:
Jian ,
maxwelian ,
akedar ,
navuho ,
sengar_vijay
Here, i attached the 8-slots magnetron cavity that I'm trying to solve and...
Dear All,
Finally , i lost the hope to solve my problem (trying to get the resonance of a magnetron cavity) by using the HFSS and i need you suggestions to switch to another software package.
Some of my friends advised me to use the Zeland Fidelity, so what do you think ??
wish to hear from...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
