Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by gaboor

  1. gaboor

    Wimax over OPNET example

    does anyone have examples or tutorial for WiMAX using OPNET? ahmed_gabr83@yahoo.com Thank you in advance
  2. gaboor

    Adding jitter to clock in Simulink

    Hi, Iam doing simulation on clock and data recovery using Simulink. I need to add a sinusoidal jitter to my incoming data. how can i do that in simulink?
  3. gaboor

    Phase modulation Simulink

    Hi I am simulating a PLL using Simulink. I am doing an experiment and i want to phase modulate the VCO output. how can i do this?
  4. gaboor

    steps about simulation PLL's behavior model in Matlab

    Hi, i know this is very old topic, however iam trying to use the simulink models. At the input and output points i have a block with Bad Link. can anyone tell me how to fix that? thanks
  5. gaboor

    Setup & Hold Time qiestions

    How can i simulate the setup and hold time of a D flip flop using Cadence?
  6. gaboor

    Delta modulation by Simulink/Matlab

    delta modulation matlab Hi, I am trying to simulate a linear delta modulator using Simulink. However i am not getting what i am expecting. i am not sure if there are some parameters i should change. I have attached a copy of my model
  7. gaboor

    need to select topic for PG degree - LVDS, PLL or ADC?

    help me pls Pll sounds good and you can find tones of stuff on the web
  8. gaboor

    Question About Simulink Simulation of Delta-Sigma Modulators

    simulink sample question Hi All, I find this topic very interesting as i am trying to build a model for 1st and 2nd order delta sigma modulation. I just started using Simulink and i wonder if anyone can help me. Thanks
  9. gaboor

    MATLAB PROGRAMING + gaussian finction

    pskmod in simulink I am a masters student and i need to simulate CDR (Clock and data recovery). I am not sure whether to use Matlab or simulink! I have basic idea about Matlab. I would appreciated if anyone can help
  10. gaboor

    Where can I get chirp generator (400Mhz-1Ghz) ?

    chirp generation Hi, Ia m looking for a chirp generator in the range 400Mhz-1Ghz. Is that avaliable in the market
  11. gaboor

    Where can i buy an ADC board?

    Re: ADC I would like to interface an analog IC (AC signals) to the computer. Simple appication :)
  12. gaboor

    Where can i buy an ADC board?

    ADC Hi, Where can i buy an ADC board? I would like to to interface an Analog IC to the computer.
  13. gaboor

    Metal Semiconductor Metal

    MSM was introduced in the early 1990s as a high speed photodetectors. Thes devices consist of aletrnate "fingers" of MSM and are sometimes referred to as interdigitated detectors. As surface detectors, they offer two imnportant advantages. Their speed is limited by the recombination time of the...
  14. gaboor

    Metal Semiconductor Metal

    Hi, Iam doing some research on Metal Semiconductor Metal Photo detectors. Does anyone have usful resources for that?! MSM-PD is still a new topic and its still an active area. I have a couple of papers about it, but the equations are not very clear!! Please if anyone can help Thanx
  15. gaboor

    IV characteristic of PIN diodes??

    I think there is a maximum voltage that you must not exceed otherwise the diode will burn!!
See more

Part and Inventory Search

Back
Top