Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by e_ali_e

  1. E

    PHC simulation with COMSOL

    Hi Everyone I am fresh user of COMSOL, I want to simulate the photobic crystal structures with this software, but I could find only one example related to PHC, I would be happy if anyone could help me. thanks
  2. E

    Material for getting the Band structure in bandsolve

    bandsolve Hi how can i set the material for getting the Band structure in bandsolve for Metallic Phc? cheers Ali
  3. E

    Where can I get the Rsoft 8.0 software ?

    Hello everybody i want Rsoft version 8.0 . i want to see how can i get it? Cheers ALi
  4. E

    Metallic Photonic crystal band structure Rsoft 5

    Hi everybody i am using Rsoft version 5. and i want to know whether can i get a band structure of Metallic Photonic Crystal? if yes please help me step by step, because i dot know what should i do. Cheers Ali
  5. E

    opamp design please help me ( emergency)

    Dear friends my professor has asked this project fully diffrential CMOS opamp design, as a school project for one of my courses, and as i am not the student of I.C design p, i dont know, what should i do. and this is really vital for me, i will be really grateful if you help me, i am sure you...
  6. E

    mode solving in optiwave or other software

    hi everybody i want to find the modes( 0, 1,2,3,..) of photonic structure for example hexagonal in OPtiwave software , but i dont know how should i? if anybody know how can i get this, please email me, if you know by other software please help me it is really vital for me...
  7. E

    lecture in ppt format about microelectronic fabrication

    microelectronic introduction lecture hi everyone i need a lecture , if it is possible in PPT format, about electronic fabrication, such as transistors,... please help me
  8. E

    Help me design an opamp with specific parameters

    opamp design i want to design a opamp with this features, please help me it is vital for me. Av>100000 Rin>10M Rout<100 ohm Vcc=10v single supply PM(phase margin)>70 for f=1 Wu(unity gain frequency)>.2*fT B(beta)<200 we should consider the fT please send me the response to my email or to...
  9. E

    LIFO in qu(at)rtus, how to simulate

    LIFO in quartus dear friends i want to simulate LIFO by quartus but i dont know how please help me
  10. E

    How to simulate 12-fold quasicrystal in Matlab?

    hi i need to simulate 12-fold quaiscrystal in MATLAB, i dont know how? if you know the geometry or rule tell me.
  11. E

    fdtd matlab codes for rods in free space

    hi does anybody know how to write matlab codes fdtd for structure like square with on the corners there are rods with special dielctric constant but out of these rods is aire(free space)? please help me. i really nedd these codes.
  12. E

    fdtd photonic crystal

    hi does anybody have matlab codes for fdtd 2D square lattice crystla.in matlab. if you have please send them to my email electronic_ali.tabriz@yahoo.com
  13. E

    fdtd photonic crystal matlab codes

    photonic crystal matlab does anybody have photonoc crystal matlab codes for fdtd
  14. E

    Which microcontroller do you use or prefer and why?

    i like PIC
See more

Part and Inventory Search

Back
Top