Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
Hi,
I am working on CC$#)F6137 development board.
I want to interface 24AA02 EEPROM to write and read data from it.
I have sample code of CC430 but I am not getting which c file is useful for my application as they have provide more than 1 c file for I2C.
I want to read and write multiple...
Hi,
I am going to work on CC430F5135 microcontroller of Texas Instruments.
I searched a lot on net for sample code of it.
But I didn't found it anywhere.
Can anybody give me the link to download it. It would be very helpful.
Thanks.
Hi Stemmer,
Thanks for the reply.
Yes you are right. I have checked this code with 24C08 and its working good.
But not with 24C64.
So i would like to know what is the difference between AT24C64 and AT24C08.
If you have used it with any LPC microcontroller than let me from where i will get...
Hi ckshivaram
I have read the datasheet and have follow the proper format as i said if i write only one page, i am able to read proper data.
But the problem is if i am trying to write about 5 pages, i am not able to read proper data.
So if you have used this eeprom then pls let me what i am...
Hi
I am trying to read and write data to AT24C64.
I am using it with LPC2387 and used sample code of i2c provided by nxp.
My problem is when I write and read single page its working fine.
But when i try to write multiple pages and than try to read all pages, its not working.
I am too much...
Hi,
I am trying to store data in EEPROM by page write and Read from same address.
But I am not able to read proper data from EEPROM.
I am using ST24c08 interface with LPC2387.
Below is my code. Please check it and let me know where I am wrong...
Hi,
I am using MCB2300(LPC2387) Board from Keil.
I want to use it with my laptop.
So I need usb JTAG.
I found that ulink 2 is suitable for it.
but i need cheapest usb jtag for it.
can anyone suggest me any usb jtag suitable for me?
Thanks
Re: P89C51RD2 programmer
Ok..
thanks for suggestion.
I think you get it wrongly..
I didn't ask your mail id for any technical help..
Anyways I will contact you soon.
Bye..
Re: P89C51RD2 programmer
Hi
Thanks for all your help and time..
i will change it.
Thanks once again..
can you please give me your email id..
i wanted to talk with you something personal, if you don't mind?
bye...
Thank you once again..:razz:
Re: P89C51RD2 programmer
Hi
thanks for the suggestion...
it's very helpful for me.
what about the code. he had submitted hex file too.
I have to change it or what?
Thanks
Re: P89C51RD2 programmer
Hi
Thanks for the suggestion.
But the problem is PCB is ready and it was made by someone who left the job and now i have to work on it..so it will take too long time to change schematic and all that.
so please provide me the suggestion from where i can get schematic...
Hi
I want reference schematic of programmer for P89C51RD2.
If anyone has please provide me. it will be very helpful to me.
or any links for that will be appreciated.
Thanks
Dhaval
Hi,
I want to make contactless smart card reader based on RFID.
I will interface it with my ARM7 board(LPC2387)..
NXP has provide one reference schematic for smart card reader with P89C51RD2.
But I have to interface it with ARM7 board.
has anyone did it before?
please suggest me how to...
Hello Everyone,
I have downlaoded sample code of USB HID of LPC2368 and I am using to test it with LPC2387.
But code is not working properly.
LED of USB connect is blink while I am attaching USB that means it connects properly But its not able to transfer data.
I don't know what is wrong in my...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
