Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by CY.Lim

  1. C

    Nanosim Simulation error....

    Hi. All. I'm sorry , I don't English good well. I'll ask you questions using Google Translate. I used a nanosim for circuit verification, but I got an error. The error message, "FATAL:NonoSim:0x4110426d:Hspice vector read error: incorrect radix line length, expecting 9, in...
  2. C

    Plz. I want to use *.vcd or *.vec file in Verilog HDL

    plz. I want to use *.vcd or *.vec file type input data in Verilog HDL Hi. all. I'm sorry. I don't english good well. I designed circuit and to make TEST module for varification using Verilog HDL. TEST module's input data is *.vcd or *.vec file. ----------------------------------- *.vcd...
  3. C

    Plz. I want to use *.vcd or *.vec file in Verilog HDL

    I didm't find the category. but thank you for your help.
  4. C

    Plz. I want to use *.vcd or *.vec file in Verilog HDL

    Hi. All. I'm sorry. I don't write english very well... I designed Circuit and to make TEST Module for verification using Verilog HDL. TEST Module's input type is *.vcd or *.vec file. *.vcd type | *.vec type $scope module TOP $end...
  5. C

    How to calculate down to more than four decimal point?

    Thank you for your help. .option measdgt=6,7,8 so on..
  6. C

    How to calculate down to more than four decimal point?

    Hi all. I'm sorry. I don't write english good well. I use '.meas command' in hspice. so I get file '*.mt' file. The file is calculation value of voltage. The value is measured to four decimal point, 'x.xxxx' but I want to see more than four decimal point 'x.xxxx~' at least six. 'x.xxxxxx'...
  7. C

    Please, is anyone very familiar with hspice? Specifically, how to combine .ms(mt)# file in hspice

    Re: plz. anyone very familiar with hspice? how to combine .ms(mt)# file in hspice Thanks. erikl. I'm sorry. I don't understand your advice. Perhaps, I didn't enlighten you about my question. But, your advice is very helpful. So, I find another method. This is not 'cat' command. I use '*.perl...
  8. C

    Please, is anyone very familiar with hspice? Specifically, how to combine .ms(mt)# file in hspice

    Thank you for your help. I have 1 question. I enter command which cat LV_nMOS_vth.ms[0-4] > LV_nMOS_vth.ms in terminal. I write command which cat fileName.ms[0-4] > fileName.ms in terminal in hspice. so, I get file.ms I want to get file after simulation right away. How to write .sp file...
  9. C

    Please, is anyone very familiar with hspice? Specifically, how to combine .ms(mt)# file in hspice

    plz. anyone very familiar with hspice? how to combine .ms(mt)# file in hspice hi all. i'm sorry. i don't write english good well. I wanna measure threshold voltage and saturation current of mosfet in hspice using measure command. After simulation, I get ms0~4 file which is coner simulation...
See more

Part and Inventory Search

Back
Top