Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by cent

  1. C

    Alternate option for multidrop network like RS485

    Could be SNAP ? It's media independent. Can be used peer-to-peer or master-slave. h--p://---.hth.com/snap/ And free. Regards,
  2. C

    1000BaseFX to 100BaseFX connection possible?

    Fiber switches works at one speed only. You can't connect a Fiber Gigabit port on a switch to a 100FX switch port on another. To connect them, you could use: 100FX to 10/100 Base T RJ45 converter and A small 10/100 Base T switch with Fiber Gigabit port included
  3. C

    SAS protocol in slot machines ?

    sas protocol Anybody has technical information on SAS protocol used on IGT's slot machines ? I couldn't find any tech. information on SAS ( Slot Accounting Software). It is a serial communication protocol used on slot machines to send accounting information to a central host. Regards, cent
  4. C

    Metal Sunt Resistor - Wich material?

    Nickel-Chrome Alloys have high Temp coeff and aren't easy solderable. For shunts with hi-stability you need Manganina, Constantan or Advance alloys. Regards, cent
  5. C

    89s52 program using serial port

    at89isp I use PonyProg adapter and software for AT89S micro. www.lancos.com/prog.html Adapter described on: AVR ISP (STK200/300) parallel port interface Please note that adapter is AT89S compatible. Regards, 8O
  6. C

    Req: simple frequency counter project

    https://www.alternatezone.com/electronics/freq.htm It's a 6 digits frequency counter. Up to 40 Mhz. Schematics and PCB included :D
  7. C

    looking for an inductor...

    Look at: www.digikey.com They sell a lot of components ( SMD coil/inductors too ) Full catalog, including specs and prices Regards, cent
  8. C

    TCP/IP DOS boot disk - any ideas?

    Go to: https://www.redoak.co.uk/hpdload.html It could be useful. Not exactly what you need, but near. It works Regards, cent
  9. C

    Current measurement Shunt

    Hi, Nichrome is used for Power resistors or Toasters. Bad as a shunt. It has a high temp coefficient. Constantan is better. It's a classic alloy for shunts. But 5A is not so high. Why don't use several low tempco standard resistors in parallel instead of building a custom one ? Regards, cent
  10. C

    How to design two serial ports on the 8051?

    a) Read Atmel Application Note ANM055 to get a second Async Interface on 80C51 b) Or use a 8051 with two serial ports. ( Dallas - MAXIM) c) If you use an external UART, you will waste a lot of I/O pins. d) Another option, but I don't test it yet: An Atmel 89S8252 has an SPI interface. You can...
  11. C

    What is the GDSII flow in ASIC design?

    gdsii.pdf GDS II is a format used on IC masks generation. It was developed by Calma several years ago. You can read more about this on VLSI Design Books. You can read: https://www.rulabinsky.com/cavd/text/chapc.html Regards,
  12. C

    Need schematic of Atmel SPI programmer

    atmel spi 1- Go to Ponyprog: www.Lancos.com/prog.html 2- Download software 3- Build the AVR ISP parallel port interfase described there. You can also use it for Atmel AT 89S. Please, read help file ( AT 89S needs to configure " invert reset" on programming software) Regards,
  13. C

    Help:Inductance measurement ckt needed

    Nice LC measurement circuit using 8031-like uP at: https://www.hw.cz/constrc/lc_metr/ Similar LC meter using PIC at: **broken link removed** Regards,
  14. C

    Looking for bar code schematics

    barcode schematics A simple barcode scanner description can be found at: **broken link removed** Regards,
See more

Part and Inventory Search

Back
Top