Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by Bjtpower

  1. B

    Understanding SRAM current consumption-71V35761S166PFGI

    Hi, I am sorry but i did not understand How you calculated or interpreted dynamic current consumption? If you dont mind, can you please explain step by step to understand clearly.
  2. B

    Understanding SRAM current consumption-71V35761S166PFGI

    Hi, Please find datasheet https://www.renesas.com/us/en/document/dst/71v35761-datasheet
  3. B

    Understanding SRAM current consumption-71V35761S166PFGI

    How to get typical current consumption? Assumed Clk frequency: 200MHZ, Duty cycle: 0.5
  4. B

    Understanding SRAM current consumption-71V35761S166PFGI

    Hi, I have SRAM 71V35761S166PFGI in my circuit and i wanted to check worst case current consumption for the same IC. i have passed through datasheet and i am confused getting exact max current required for the SRMA IC. SRAM is interfaced with Microcontroller
  5. B

    Total current required by OPAMP

    Hi, How to shift that? i did not get it Can you guide how to that?
  6. B

    Total current required by OPAMP

    Hi, I tried to do simulations. and getting few results, sharing in attached zip files. I am able to get impedance for ADC 7484 so RL- i kept as 1000R. https://www.analog.com/media/en/technical-documentation/data-sheets/AD7484.pdf Can someone help how much Impedance i need to put as a replica...
  7. B

    Total current required by OPAMP

    AIN+ to AIN- has max voltage of 5V, F=1KHZ, V+=+5V, V-=-5V
  8. B

    Total current required by OPAMP

    I wonder, how did you get 2mA?
  9. B

    Total current required by OPAMP

    Hi, I am using AD 8022 as difference amplifier (First stage) and Level shifter (Second Stage) as below. Can you please help what do you mean by "if you want to use max linear output"? Do you mean entire range of Supply voltage
  10. B

    Total current required by OPAMP

    Hi, I am trying to do paper calculation for current requirement for OPAMP AD8022 https://www.analog.com/media/en/technical-documentation/data-sheets/ad8022.pdf I would like to make sure how much current required by OPAMP when it is in operation mode. I have captured below snapshot from PAGE...
  11. B

    Solving difference amplifier with capacitor with equations

    Hi, I would be happy if you help with me some equations, how they play roles? No matter if they are smaller or higher values.
  12. B

    Solving difference amplifier with capacitor with equations

    Hi, I would like to learn Difference amplifier and its equation when capacitors are connected in Feedback like below My intension understand capacitor impact and its equation for learning purpose.
  13. B

    Beginner for FPGA

    Thank you very much for the details and boosting confidence for FPGA, Really apprecited. Keep in touch.
  14. B

    Beginner for FPGA

    Hi, I am new for FPGA and i have intrest in FPGA. Recently i have purchased ZYBO Z7 for learning and pursue my passion. Can you please help or advice from where i should start? I have 12 years experinece in hardware (Worked on 32 bit Microcontrollers, Power supplies, analog and digital design).
  15. B

    What is Directive and standards?

    Hi KlaussT, Apology for short description. I am designing Voltage n current measurement devices.. which will calculate power in 3Ph. This equipment would sit in industrial site to measure the power of there high power devices. We can take reference of fluke or hioki power analyzer or recorder...
See more

Part and Inventory Search

Back
Top