Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by balagbc

  1. B

    power ON problem with P- MOSFET

    @FvM your suggestion really helped me and worked perfectly. thanks mate
  2. B

    power ON problem with P- MOSFET

    will(Si2323) it withstand in low voltage input(3.7v) at minimum 2A load?
  3. B

    power ON problem with P- MOSFET

    Dear all iam facing problem with power supply switched by P-MOSFET. For voltage above 4v the load(GSM modem) works fine but if the voltage fall below4v the modem couldnt get power supply properly. i dont knw wheather problem in mosfet or modem. pls help me with this problem.
  4. B

    Interfacing BLE with Bluetooth Tag sensor

    Hi every one, can u tell me how to interface BLUETOOTH TAG(slave) With BLE(RN4020)(master) controlled by Micro controller. is there any command for BLE module(RN4020) to scan multiple tag sensor? thanks in advance
  5. B

    Power over Ethernet connector selection and connection ?

    @SunnySkyguy i ddnt get it. tell me is it possible to transmit 12v supply directly in unused spare cable?
  6. B

    Power over Ethernet connector selection and connection ?

    Dude thats why iam confusing over selecting center tapping ethernet connector. if i select the POE connector will it cause change in connection in our circuit. do we need special power circuit to convert power,transmitting over the ethernet . if i have some voltage in my pcb should i connect...
  7. B

    Power over Ethernet connector selection and connection ?

    hi all, i have conflict over selecting POWER OVER ETHERNET connector and connection between connector and controller. i need to send +12v and data in same RJ45 connector. i select some POE+ magnetic jack connector. but i dont know how to connect 12v and data line.if i transmit both power and...
  8. B

    0-100A DC current measurement method using shunt resistor

    @Ranbeer Singh .. what type of measurement ll give accuracy whether top load or bottom load shunt resistor?
  9. B

    0-100A DC current measurement method using shunt resistor

    hi there, please suggest me best DC current measurement circuit using Amplifier . thanks in advance.
  10. B

    SIM800C sim connection problem?

    sim800c working fine with 64kb sim but not in 128kb simcard. tell what yo do ? thanks in advance.
  11. B

    ripple voltage blocker circuit for 24DCV 100A?

    from 3ph supply --->>step down transformer----->>bridge rectifier---->>filter capacitor---->>> load
  12. B

    ripple voltage blocker circuit for 24DCV 100A?

    thanks for reply folks . got some ideas from ur reply's
  13. B

    ripple voltage blocker circuit for 24DCV 100A?

    hi folks, my voltage(24v,100A) circuit producing 5v ripple i couldnt reduce the ripple voltage.if i use this voltage my equipment surely ll get damage . so wht i should do now ? how to reduce the ripple voltage ? capacitance in parallel not helping me ?pls suggest anyother method any other method?
  14. B

    controller selection for marine automation product

    hi everyone, please tell me what are the high end micro controller available in market and particularly for marine control system(high int memory,pin etc)also in need RTOS inbuilt in that controller thanks in advance
  15. B

    ripple voltage measurement method?

    hi everone pls tell me how to measure the ripple voltage on battery input during the charging period. my pic controller is 10bit adc . the ripple voltage may be in between 100mv to 200mv. (ie. 0.1v) i tried to measure the ripple voltage using voltage divider but the problem is i couldnt get...
See more

Part and Inventory Search

Back
Top