Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by anthrax

  1. A

    ICD2 Problem! Cannot program dspic33fj128mc710!

    dspic33fj icd2 Hi, I'm using ICD2 (not the org. one from Microchip, it's a clone ICD2) to program dspic33FJ128MC710. MPLAB can recognize dspic33FJ128MC710 when I connect, but when I program the chip, it say verify fault I was thinking that It's because of 5V in ICD2 and 3.3v in dspic33FJ make...
  2. A

    new USB2.0 TI DSP Emulator XDS510,Very COOL

    tds510 jtag Dear lslrf, Can you tell me the address or telephone number of 511eda.com so that my friend in Shenzen can help me buy xds510. I cannot browse to your website www.511eda.com may be some error with server. Thank you very much
  3. A

    Read program from locked Xilinx CPLD XC2C64-7VQ100C ?

    Hi guys! I had a chip Xilinx XC2C64-7VQ100C that was program locked .Could someone read this program form this locked chip so i could burn the program to another fresh chip. Anny helps will be much appreciated! Regards, H
  4. A

    Details of motion sensor connected to microcontroller

    Re: motion sensor to mcu thanks bilgekaan,this is great link.
  5. A

    Details of motion sensor connected to microcontroller

    Re: motion sensor to mcu Hi gidimiz, Thanks for your suggestion about using GPS.But GPS cannot be used under water. My project is building a ROV (remote operated vehicle) and it works under sea. And IMU is a possible choice if it is combined with compass or magnetometer. Now i give up building...
  6. A

    C30 : using printf() for LCD

    hello, I fixed my problem. thanks for reading.
  7. A

    Details of motion sensor connected to microcontroller

    Re: motion sensor to mcu sorry, I searched for postion navigating.I found IMU (inertial measurement unit) (3 accelerometer sensor+3 gyroscope sensors for 3 axis) can deal with my requires.But at last ,i found that stand-alone IMU will not accuracy after long-term period(about 10 seconds). IMU...
  8. A

    Details of motion sensor connected to microcontroller

    Re: motion sensor to mcu IanP, i know using only accelerometers sensors don't give us postion any other opinion?
  9. A

    C30 : using printf() for LCD

    hi guys! I want to use printf() function( in C30) to print characters or numbers to LCD. I modified putchar() function to print a chacracter to LCD and it worked( putchar() worked). But when i use printf() function ,it did not display anything to LCD. I look at stdio.h and i think May be my...
  10. A

    Build easy MPLAB-6 ICD-2 for PIC18F2550

    vpp mplab icd hi Blinky! some PIC can't be programmed by MPLAB ICD 2 "In the MPLAB When you choose the typr of PIC under select device, the green or red under "Microchip debuger tool support" - MPLAB ICD2 will tell you if you can debug (red ) or just program ( green ). "
  11. A

    program stand alone hex file in ICD 2

    thanks! now i know the answer,but i wonder if i choose Programer-->Program ICD 2 will start programming,then ICD 2 will program hex file which i import or another else? Because MPLAB IDE don't display which hex file be programmed Another question ,if i don't use import function but try to...
  12. A

    program stand alone hex file in ICD 2

    i build ICD 2 succesfully but i can't manage how to load stand alone hex file to target processcor in MPLAB IDE.i 'v been not familar with using MPLAB IDE yet. for example i want to program target processcor with hex file test.hex located in directory C:/ (path is C:/test.hex) .How can i do...
See more

Part and Inventory Search

Back
Top