Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
Hi,
I'm using repetier server on raspberry Pi 3. And I interfaced 7inch FHD Monitor(1920*1080)(Waveshare Display). I was getting the application output on the display. But all icon buttons are very small, which is very difficult to access on the touchscreen. I want to scale up this icon button...
Thanks andre,
I want to make a 3D printers for the fabrication of the plastic parts, i found that in few videos that marlin firmware with AT2560 is working fine, i want to develop the same with our PIC(8/16bit) or renesas controller(RF series). and moreover the AT2560 also a 8bit controller. can...
Thanks for your reply,
I know the difference between Controller and processor.
i asking for how to process a G code comments in PIC controllers like what they did in ATMEGA. is there any tutorials for the executing G_Code comments?
- - - Updated - - -
Hi KlausST,
Basically we can develop...
Hi all,
I found that, 3d printers are developed in atmega controller by the Marlin Software. Can we develop the printer by the help of PIC controllers or any other controllers than atmega/raspi. Please suggest any possible way of doing.
Thanks,
Thanks Vbase,
Ok. for various input supply, that vref 2.3v will be same or it will be different for different supplies.
- - - Updated - - -
Thanks Klaus,
I couldnt get that over charge indication to low.
I monitoring the battery voltage for every hour, it has been increasing by 0.4V/hr. it...
Hi all,
I have to charge a 24V 12Ah Lead Acid battery with combination of two 12V batteries in series.
I have selected UC3906 charging IC for to charge the battery.
I gone through the application note of UC3906, https://asmith.id.au/files/uc3906-battery-charger.pdf
in that they had given...
Thanks for the reply,
I need to sent it in RS232 protocal.
i just sharing the sample data excel sheet,
Name Age Place Degree
ABC 18 ZYX BE
DEF 20 YJK BE
JKL 45 WER MSc
those data has to send out through USB to RS232 converter. by selecting...
Hi all,
i have to create a tabular column with 10rows and 6columns in excel.
This tabular column data has to sent out through UART.
is is possible to sent out the data from excel to UART communication?
if it is so, please guide me.
I have been working in the renesas controller and i have a renesas E1 serier emulator. few months before i have worked in this emulator, at that time it is worked fine. but now its not detecting, some warning error showing in the device manager. when i try to update the driver, it saying as all...
--> define "huge number". Is it 1000, is it a million? ====> data's around 10,000bytes
--> what microcontroller interface do you want to use? ====> yet to decide after selecting the protocol. Mostly Renesas RX62N group.
--> only one direction, no receive, no handshaking? ====? Tx - 10,000 bytes...
Hi all,
My requirement is to send the huge number data's within a second at longest distance(500mtr to 1Km) from the micro controller. Could you suggest which communication protocol is best to use and be very easy to handle.
And one more point for you, i have to place the PTC over the coil to sense its temp. If it is over heat, the circuit has to open, when its come to normal, the circuit has to close.
I have attached the 12V solenoid datasheet, it is similar to 24V solenoid, voltage only the difference.
- - - Updated - - -
see my current flow is 650mA only, PTC has the 900mA current rating. Then how it will get heat. One thing i having the doubt, wether the PTC will work upto 900mA or it...
If anything happened in the board or some short happened means, the coil tends to activate. On that time how can i prevent the circuit to open? is there any other way to gets open?
Important thing is, if the coil gets 24V Continously means, it tends to tremendous heat. Please suggest any other...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.