Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by akshay_kul59

  1. A

    usb to rs232 converter using 18f4550

    Re: usb to rs232 converter yhygyhjC:\Documents and Settings\VINIT.AKT-FF974CC5DE2\My Documents\desk\vinpedia\GSMGPRS\GSM-GPRS Modems and GSM-GPRS Modules.htm
  2. A

    SIP(Session initiation protocol) for Voip Performance

    fo
  3. A

    usb to rs232 converter using 18f4550

    Re: usb to rs232 converter Can you kow about avoiding found new hardware wizard (installing INF files throgh program in .net)
  4. A

    usb to rs232 converter using 18f4550

    Re: usb to rs232 converter Can you kow about avoiding found new hardware wizard (installing INF files throgh program in .net)
  5. A

    usb to rs232 converter using 18f4550

    Re: usb to rs232 converter Can you kow about avoiding found new hardware wizard (installing INF files throgh program in .net)
  6. A

    Smart Card Reader development

    card reader development please tell me solution for it
  7. A

    Problems with SIM300 as it doesn't detect the sim card

    sim300 v3.04 Hello, I have designed my board as per V2[1].01 for SIM300. But I am not getting whetherVext is out put pin or input. The voltage ranges I am getting on designed board are Vbat = 4.6V Vext =3.01 if I attached D202 output on Vext pin considering Vext is input pin. I am not...
  8. A

    How can I drive 5v,2A from USB port

    usb 5v 2a Please can you tell me, how can I drive 5v,2A from USB port. I wont wants to use external adaptors in my system, running on USB. So I am trying to drive whole power from USB. Please if possible try to send me details,schematic as early as possible. Thaks in...
  9. A

    MAX232 interfacing with 89c51

    max232 interfacing Hi friends; Please can any one provide me C code for interfacing com port with 89c51 using MAx232. Thanks in anticipation.
  10. A

    Smart Card Reader development

    t8007bc3_rb.lib Hi irmakci & funnynypd, Thanks for your reply, I am trying to use TDA8007BHL contact type smart card reader IC, by NXP semiconductors. I have developed, hardware base to interface this IC, also I have found a application code related to my application. But I am not getting...
  11. A

    12V battery charger circuit diagram

    I have a following circuit of battery charger, please can any one help me
  12. A

    (21 POINTS HERE)Serial Printer Interface?

    Hi dear, Just try out UART transmission codes , for controlling printer by adjusting boud rates
  13. A

    BJT is definitely faster than MOS....Please acknowledge....

    bjt vs mos turn off Ya MOSFET is mostly preffered because firstly it is as faster as BJT due to advance fabrication technologies 2nd it requires less chip area than BJTs hence it is easy to fabricate mos chips
  14. A

    What is the size of ground and VCC wires?

    Ground and VCC wires It depends on how much the supply you are using in ckt. Mostly in purely electronic ckts it is arround 2.5 to 3 mm maximum.
  15. A

    Smart Card Reader development

    tdalib.h I am working on smart card reader. whether any one has worked with NXP smart card reader development board. I have a problem regarding getting header files & respected library functions code. please can any one help me regarding this. Thanking in anticipation.[/b]
See more

Part and Inventory Search

Back
Top