Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
Hi
I have a xds 510_usb2.0 Ti DSP Emulator, bought from ebay chinese made.
i have 1 setup with it to make it run with ccs studio and 1 usb driver. it shows up
as ti emulator xds 510 usb 2.0 in device manager but i cant connect with my target from ccs. please help me find a installation...
Hi
has any body used bs901 (arm9 s3c2410 based ) board.
i have one but i have no help regarding this board.i need a sample code to run on this board specially make file for gcc compiler.
shakeel
arm linux gcc toolchain
hi jerins
thanks for reply,i have compiled it by changing make file,and renaming linker file
i will read the file u mentioned too,hope it helps further
shakeel
gcc c++ linker script lpc2378
hi
now i can compile a project in linux gcc arm tool chain .but this project is for lpc 2378, i need to compile it for lpc 2368 . i need to change make file ,and linker script to compile for lpc 2368.what are the steps needed to change linker script and make file...
howto gcc arm
hi jerins
thanks for reply,i have unziped it using tar utility,plz tell me where can i find
the script file you are talking about
Shakeel
arm-linux-gcc toolchain
hi
i am new to linux ,i have installed fedora 8 kernel 2.6. and downloaded gcc tool chain for arm from (www.mikrocontroller.net).after the unzip i can c the files such as (arm-elf-gcc) in bin directory ,but i dont know how to make and compile a project for any arm7...
Re: help about ARM
Hi
First of all u need start with a IDE,for example u can start with keil uvision3 Evaluation version with real view compiler for writting and simulating ur program. evaluation version is free but with code size limitation,Programs that generate more than 16K Bytes of code...
hi
I am new to PCB designing using (PROTEUS ARES) Please tell me what is the explanation of drill mark,in (PROTEUS ARES )
i have made a pad style with pad diameter of 80 thou,and drill hole dia of 40,i kept drill mark 40(thoug i dont know what it is used for ),also i have pads of 70,30
(default...
hi
following link will help u interface adc 0804 with 89c51
https://www.freewebs.com/maheshwankhede/adcdac.html.LM35 has Linear + 10.0 mV/°C scale factor, that means for every degree rise in temperature its voltage is incresed by 10mv.u have to provide voltage (Pin 1)and ground(pin 3) to...
sim300 gsm module
hi
i never found such AT command in sim300,as far as i know Location of a BTS is the information send by operator as data,which is decoded and displayed in cellular phones,if u know the format of data u can recover the Location.
Shakeel
how to connect temperature input to adc0808
hi
u can use ADC 0804 instead of 0808 as 0804 is simpler ,also following link might be useful for u.as it is about interfacing 0804 with controller .
https://www.freewebs.com/maheshwankhede/adcdac.html
As far as lm35 is...
hi
u may use ISP programmar Software by "Adam dybkowski" and use hardware
from the link http ://www.lancos.com/e2p/avrisp-siprog.gif this for avr but works fine with 89s52.
Shakeel
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
