Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
Dear jimspring03.
I have the same problem with the same technolgy (UMC 0.13um RFCMOS). All devices in schematic netlist (SUBCKT statements missing, exactly as in your attached file) are not find in the netlist. Did you find the solution? See attached screen. Best regards, André.
- - - Updated...
Hello guys.
I am using UMC 0.13um RF technology to design a TIA. I am facing problems with Assura QRC verification. An error message appears:
ERROR (ASSREXT-88016): cap ground signal 'agnd' cannot be found.
Check if net 'agnd' exists in design ad has the correct ?netNameSpace (Schematic...
Hi Maithreyi.
I also had these errors with UMC 130nm RF technology. I am also facing problems with assura LVS run: Did you have these errors in your design? Thanks for your attention.
mmsim61 download
Hello guys....i solved the problem....mmsim61 is installed...but i have a new problem to solve. When i try to run a simulation, the following message appears:
*Error* Unable to locate 'spectre' executable in the specified path.
To set the correct path, use...
mmsim61
hello everyone....i need some help....
I have IC610 installed on Centos 5 linux, it works perfectly, but i need to install MMSIM61 to have Spectre simulator available. When i try to install it, installscape displays the message:
Previously installed products are pre-checked. If you...
installation of mmsim
Hello guys....
I'm using cadence ic610 on Centos 5. I need to install MMSIM61 to have Spectre simulator working, but when i try to install it, installscape display the following message:
Previously installed products are pre-checked. If you used an InstallScape Control...
qt warning: x error: badwindow
Firas, add the line bellow to your xorg.conf file:
Section "Extensions"
Option "Composite" "Disable"
EndSection
i had the same problem and the solution above worked fine for me. By the way, are you going to install mmsim61? I have teh CD's but i couldn't...
ubuntu ic5141 libc.so.6
Hello None34...thanks....i've added the line to my bashrc file and the installation is ok now, but, i can't run cadence because of the problem glibc problem: . I'm trying to run IC5141 on Ubuntu now. I have the IC610 installed on Centos 5 and runs perfectly, but the...
ubuntu ic5141
Hello guys....i installed sucesfully cadence IC610 on Centos 5. I have the MMSIM61 Cd's, but i didn't install them yet. How can i install MMSIM61 to run spectre simulator on IC610? Thanks...
ic5141 on centos 5
Hello guys....i had the same problem with IC5141 on Centos 5.
I didn't find where the .tcshrc file is located..... can anybody help me? thanks....
libgdbm.so.2 ubuntu
Hello geniusstation
I downloaded IC5141 but i couldn't installed because there are only 3 CDROMs. I also tried again to install IC5033 on Centus 5 but the follow message appears:
#################################
Are your selections correct? [y/n] y
Generating detailed...
installing cadence on ubuntu
Thanks for the instructions geniusstation.
As soon as i get IC5141, i'll try it on ubuntu 7.10. By the way, is it better to use ubuntu 7.10 instead for Centus 5?
thanks...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
