| Author |
Message |
molloy
Joined: 14 May 2003
Posts: 59
Helped: 1
Location: Milan
|
 21 May 2003 10:18 Balanced amplifier |
|
|
|
I have to design a balanced amplifier (UHF). I'd like to simulate even the 2nd harmonic to understand its behaviour in the circuit but i dont know well how to do. The second harmonic could cause a saturation of the amplifier and so it is very important to know its influence. The problem is that i just have an equivalent circuit of the output of the transistor (and it doesnt exist a non linear model of the transistor)
thanks
|
|
| Back to top |
|
 |
Borber
Joined: 01 Jan 1970
Posts: 1492
Helped: 111
|
| 21 May 2003 12:05 |
|
|
|
The second harmonic of what? Is it componnent of input signal or...
If your amplifier is not overdriven to nonlinear region (-1dB compression) you will have no problem with second harmonic.
Your question is not quite understendable!
|
|
| Back to top |
|
|
nandopg
Joined: 26 Apr 2001
Posts: 248
Helped: 5
|
| 21 May 2003 13:26 Need more details... |
|
|
|
Dear molloy,
Let us know what kind of balanced structure you are using in your project. Basically there are two ways to get a balanced amplifier: a push-pull connection and a connection using power combiner/splitter.
The push-pull connection has the advantage to cancel the even harmonics (including the second) and because of that, in some case, is the preferable connection.
If you are using power combiner/splitter to get the balanced structure you are right to be worried about the second harmonic specially if you are pushing the active devices into class AB to get a better efficiency.
To try to provide you some help it would be necessary to know some details about your project as:
1- How are you connecting the active device.
2- What is the active device you are using
3- How much efficiency are you looking for
4- Design targets as frequency response, output power, driver level, etc...
NandoPG
|
|
| Back to top |
|
|
molloy
Joined: 14 May 2003
Posts: 59
Helped: 1
Location: Milan
|
| 21 May 2003 14:28 |
|
|
|
You are right, the both of you. Well:
I choose a configuration with a balun, just to reduce the second harmonic.
The amplifier works in AB mode (and so i need a 2nd harmonic characterization)
The output power is very high, lets say about 54-55dBm
The band is UHF
emmm i cant say nothing about the device unfortunately, because of my job. Anyway i hope you could help me the same
thanks
|
|
| Back to top |
|
|
nandopg
Joined: 26 Apr 2001
Posts: 248
Helped: 5
|
| 21 May 2003 17:41 Some points... |
|
|
|
From you last post:
1- Push-pull configuration in RF PAs is preferable when you have transistors in twin package and in class B operation. In this case you have a strong decreasing in all even harmonics. By the way true push-pull operation is only defined in Class B operation.
2- As you go into class AB the use of baluns as a summing device shows any advantage and an disadvantage comes up: you don't have isolation between the transistor. This means, if the PA for any reason get unbalanced the likelihood to blow the transistors is pretty high.
3- For Class AB and Class A the transistors should be connected through a power combiner/splitter in order to have insensitivity respect to possible unbalancing between the two halves of the PA. This is even true at the power level you mentioned.
4- As a rule of thumb for UHF Class AB devices connected through a power combiner/splitter the second harmonic is about -40dBc. You can use this figure to determine the order of the harmonic filter.
Concluding: For the reasons presented you should not use baluns as summing device for a Class AB PA.
NandoPG
|
|
| Back to top |
|
|
molloy
Joined: 14 May 2003
Posts: 59
Helped: 1
Location: Milan
|
| 23 May 2003 7:54 |
|
|
|
The ldmos i use is the type with two devices in a case. I will use two of these in a balanced configurations (and so with a 90° hybrid), but im forced to use a push-pull configuration with a balun because of the output impedance of the LDMOS (about 3-3.5ohm) that would be very difficult to match.
Just to be clear i include a data-sheet of a similar LDMOS
thk
stefano
|
|
| Back to top |
|
|
