| Author |
Message |
fighter
Joined: 06 Dec 2002
Posts: 15
|
 12 May 2003 3:16 chipscope |
|
|
|
Hey,everybody,i'm suffering by useing chipscope ,would you like to
show me some suggestions with my appreciation!
my enviorment:
1,fpga :virtexII xc2v3000
2,eda tool: ise5.1
3,chipscope :4.1i or 5.2
I want to use chipscope to capture some signals from my fpga,
but i cannot configure fpga with chipscope corretly,the below
messages display :
configure failed,done pin is low!!!
i'm not sure the true reason,because i can configure fpga with impact
correctly(jtag mode),so the jtag chain interface should be ok,
Plus i got some information from xilinx website,that chipscope5.2pro is
designed to work with ise5.2,and chipscope5.1 is designed to work with
ise5.1,the same reason,so chipscope4.1 is designed to only work with
ise4.1????is it right?
For i have chipscope4.1 and chipscope5.2
and i have ise4.2 and ise5.1.
What your suggestion about compatibility between ise & chipscope???
Thanks a lot!!!!
|
|
| Back to top |
|
 |
sb
Joined: 06 Mar 2002
Posts: 13
|
| 18 May 2003 10:27 Chipscope |
|
|
|
Hello,
Chipscope only works with the respective ISE version. If you have Ise 5.1 it only works with Chipscope 5.1 but not the other way. Get the proper version for ISE 5.2.
SB
|
|
| Back to top |
|
|
happytronic
Joined: 14 May 2003
Posts: 9
|
| 24 May 2003 16:07 chipscope |
|
|
|
Hi,
I do not know much about chipscope, but mabe you need a pullup on your "done" signal???, this can be done internaly to the FPGA I would think.
give me feedback please, I'm interested.
|
|
| Back to top |
|
|
kaol
Joined: 25 Sep 2001
Posts: 32
|
| 26 May 2003 4:08 |
|
|
|
fighter
I recommand u check the circuit more carefully, I think maybe there were some wrong in the line connection.
|
|
| Back to top |
|
|
visualart
Joined: 21 Dec 2001
Posts: 582
Helped: 26
|
| 26 May 2003 4:47 |
|
|
|
| Maybe your selected chip isn't enough larg for your design.
|
|
| Back to top |
|
|
sb
Joined: 06 Mar 2002
Posts: 13
|
| 27 May 2003 21:56 Chipscope version bug |
|
|
|
Hello,
If you don't belive me just read xilinx's website:
http://support.xilinx.com/xlnx/xil_ans_display.jsp?iLanguageID=1&iCountryID=1&getPagePath=16875
Family: Software
Product Line: FPGA Implementation
Part: ChipScope Pro
Version: 5.2i Record Number: 16875
Last Modified: 03/21/03 16:29:12
Status: Active
Problem Description:
Keywords: ChipScope, Pro, 5.2i, 5.1i, compatible, version
Urgency: Standard
General Description:
After I install v5.2i software, my v5.1i software no longer works. How can I run both versions on the same machine?
Solution 1:
This incompatibility is a known issue and will be fixed in a new release of 5.1i ChipScope Pro. The new release is Release 4 of 5.1i ChipScope Pro, and it will be available soon at:
http://www.xilinx.com/ise/verification/cs_pro_get.htm
|
|
| Back to top |
|
|
zape
Joined: 10 Jul 2003
Posts: 104
Helped: 9
Location: Spain
|
| 10 Jul 2003 18:29 |
|
|
|
| What probe are you using? Multilinx or Parallell? I suffered from a lot of similar troubles with multilinx. I had to retry a lot of times to get my devices configured. Changing to parallell probe and the same setup I succeed inmediatly.
|
|
| Back to top |
|
|
ch_wen
Joined: 08 Feb 2002
Posts: 29
|
| 11 Jul 2003 16:20 |
|
|
|
| sb is right, you have to get chipscope 5.1i to work along with your ISE 5.1i or upgrade your ISE to 5.2i. No other solutions. I'm wonder why there are so much unrealistic suggestion after sb's post?
|
|
| Back to top |
|
|
