| Author |
Message |
Sanath Embedded
Joined: 23 Jan 2009
Posts: 51
Helped: 1
|
 09 Apr 2009 12:51 transfer art to pcb |
|
|
|
|
Hi Guys,
The common problem in India is to get it done this fabrication of PCB.Even though there are lot of firms that fabricate the PCB but the ordered quantity should be very high else the order value will be around 5k for the minimum samples and also the time factor ( around 10-15 days). So can anyone help me to do the Inhouse PCB fabrication for the sample PCB modules.
Regards
Sanath
India
|
|
| Back to top |
|
 |
Google
AdSense
|
09 Apr 2009 12:51 Ads |
|
|
|
|
|
|
| Back to top |
|
|
isurug
Joined: 22 Aug 2008
Posts: 18
Helped: 1
|
09 Apr 2009 13:21 transfer artwork to pcb |
|
|
|
|
Hi Sanath,
you might give this method a shot! its pretty easy, all you need is a laser printout of mirrored B/w laser printout of the cct and some light.
check this link out
http://users.bigpond.net.au/vk3yng/pcb/making_pcbs.htm
for boards
http://www.computronics.com.au/kinsten/prices/
basically the quality is very good for prototyping. u can go down to 8mils of track if ur print and lighting is good!
-isuru
|
|
| Back to top |
|
|
pranam77
Joined: 22 Apr 2008
Posts: 1071
Helped: 94
Location: Mangalore(India)
|
09 Apr 2009 15:59 paper phenolic drilling |
|
|
|
|
Hai Sanath Embedded
Send your Layout files in 100% Scale, with JPG or PDF or BMP or any common format and get even 1 PCB fabricated within 4-5 days. They even do prototyping and assembling contracts. Contact "www.united77.com" for your needs.
|
|
| Back to top |
|
|
hameeds01
Joined: 23 Aug 2005
Posts: 308
Helped: 15
Location: NUST Islamabad
|
18 Apr 2009 18:28 pcb art transfer |
|
|
|
|
Howto make a PCB in Home
It is simple, Toner Transfer method
Materials and equipments required
1. Ordinary Iron Box
2. hacksaw or hacksaw blade
3. low cost hand drill
4. Copper clad sheet (Glass epoxy is best for this method, if possible don't use paper phenolic )
5. Ferric Chloride (100 gm can be used for making 250 boards)
6. ART PAPER (Glossy paper available in office stationary store)
7. Plastic tray
8. Computer and Laser Printer ( Optional)
Steps
1. Make a fresh print out of your PCB layout in ART PAPER using a Laser Printer
(Transfer it as earlier with in 2 to 3 hours)
2. Clean the PCB with metal scrapper which is available Kitchen
( Cleaning is very critical, so clean it as shiny as possible)
3. Dry the PCB with a cotton waste
4. Power on the Iron Box with maximum heat setting
5. Place the art paper over the PCB copper side (make sure no air bubble )
6. Place the Iron Box over the PCB copper side for 3 to 5 Minutes , press and make a little move(depends on Heat)
7. Remove the Iron Box and put the PCB in to water
8. Sock it well and remove carefully the paper
9. Now you can see the toner stick in to the copper and paper layer can remove separately.
10. Sock and remove all part of paper (small portions of paper make short circuit)
11. make a solution with 10 to 25 gm of Ferric Chloride and 1/2 Lit water
12. Put the PCB in the solution and make to and fro motion until all part of the excess copper will remove.
13. Now Your PCB is Ready for drilling.
1mm holes are suitable for resisters, IC, diode etc
I have made lot of PCBs with this method.
Expense for making minimum setup is PCB (1'x1') - Rs.150($4) Hand Drill Rs.120($3)
Ferric Chloride(150 gm) - Rs.120($3) , Art paper, Hacksaw , Plastic Tray Rs.120($3)
TOTAL Approx. Rs.500 ($12)
|
|
| Back to top |
|
|
