| Author |
Message |
elbadry
Joined: 06 May 2005
Posts: 358
Helped: 62
Location: Egypt
|
 30 Apr 2006 8:15 Calibre in Cadence |
|
|
|
|
Dear All,
I am using Calibre under Cadence Environment to perform Parasitic extraction. How can I use Calibre to generate a view that can be simulated in Cadence?
|
|
| Back to top |
|
 |
Khaled Ibrahim
Joined: 02 Oct 2004
Posts: 13
Location: EGYPT
|
| 04 May 2006 18:07 Re: Calibre in Cadence |
|
|
|
|
Hi Adel,
Choose "CALIBREVIEW" from the "Outputs" tab, and after simulation you'll find a "Calibre" view generated for your cell. Then create a new "Hierarchy-Editor" Cell View (Config) in your test bench cell and change the "View to Use" of your circuit from "Schematic" to "Calibre". Then Save and Open the "Config" view and normally use "Analog Environment" to simulate your new "with parasitics" circuit!
Hope this will be useful 
|
|
| Back to top |
|
|
elbadry
Joined: 06 May 2005
Posts: 358
Helped: 62
Location: Egypt
|
| 08 May 2006 9:26 Re: Calibre in Cadence |
|
|
|
|
Thanks dear Khaled
I tried this but I get an error:
//
*WARNING* dbOpenCellViewByType: Failed to create cellView (cell_name calibre) from lib (libname) in 'w' mode. Must specify a valid viewTypeName.
//
Any ideas how to resolve this?
|
|
| Back to top |
|
|
Khaled Ibrahim
Joined: 02 Oct 2004
Posts: 13
Location: EGYPT
|
| 08 May 2006 17:08 Re: Calibre in Cadence |
|
|
|
|
| so strange! did you try to make the same way of calibreview creation on different libraries or cells?? and does calibre normally outputs parasitics using any other view?? (ex: spectre, eldo,..)
|
|
| Back to top |
|
|
elbadry
Joined: 06 May 2005
Posts: 358
Helped: 62
Location: Egypt
|
| 08 May 2006 19:58 Re: Calibre in Cadence |
|
|
|
|
No, I didn't try to use it on another cell...
I can see parasitics using Calibre interactive. Also, parasitics are visible if I make the output a spectre netlist...
Can this be a problem with the Kit?
|
|
| Back to top |
|
|
Khaled Ibrahim
Joined: 02 Oct 2004
Posts: 13
Location: EGYPT
|
| 09 May 2006 19:30 Re: Calibre in Cadence |
|
|
|
|
No, I don't think it's from the design kit. It's of one of two, calibre or you
1. which calibre version are you using?
2. make a new library and instantiate any simple device in a cell, then try to extract its netlist in a calibre view, and let's see if something still going wrong...
|
|
| Back to top |
|
|
morence
Joined: 11 Jun 2008
Posts: 1
|
| 11 Jun 2008 4:40 Re: Calibre in Cadence |
|
|
|
|
Hi,
I have same problem in calibreview generation,
Is there any solution for it,
Parasitics is also visible in a spectre netlist but the Calibreview can not be created as following,
"*WARNING* dbOpenCellViewByType: Failed to create cellView (cell_name calibre) from lib (libname) in 'w' mode. Must specify a valid viewTypeName"
Thanks,
|
|
| Back to top |
|
|
