AT commands in Ericsson T28

EDAboard.com Forum Index -> Microcontrollers -> AT commands in Ericsson T28

Author

Message

nofnof

Joined: 03 Mar 2005
Posts: 31
Helped: 2

19 Mar 2005 12:58 ericsson at command

as i mentioned in my last posts , im preparing my graduation project in microcontroller , now i have a new task , to bring the important AT commands in Ericsson T28 and the special ones for the sms , please help me to get those commands , and please i need help how to send them correctly by the HyperTerminal via RS232 cable
Thanks

defnfo

Joined: 11 Jun 2003
Posts: 70
Helped: 5

19 Mar 2005 18:19 ericsson at commands

i see yput old posts
i have ericsson a1018 and it is all right
but connection speed i have: 9600 and flow contol: none
i work with hyper terminal
see my old answer

see http://www.serasidis.gr/circuits/smscontroller/smscontroller.htm
and ericsson T28 _R1A.zip file

nofnof

Joined: 03 Mar 2005
Posts: 31
Helped: 2

19 Mar 2005 21:41 at commands ericsson

yah i see
thanks for the link , i found everything i want in it , and thanks for ur care

traxonja

Joined: 06 Apr 2004
Posts: 109
Helped: 1

20 Mar 2005 21:31 ericsson t28 max232

Message to: "defnfo"...

Hello,

Does your ericsson go to shutdown when allways connected to battery charger?

It happens to my siemens S25 and all other siemens's Sad

Trax

defnfo

Joined: 11 Jun 2003
Posts: 70
Helped: 5

23 Mar 2005 10:25 at commands for ericsson

i have only small experiment with ericsson 1018
because i never use data cable together chargar cable,
but phone works with online charging as long as you want

kuldeep

Joined: 06 Apr 2005
Posts: 43
Helped: 1

06 Apr 2005 13:21 ericsson t28

To use Hyperterminal for transmission of AT commands:
> Configure the COM port connetion keeping in mind the BAUD RATE of the module, flow control should ne none, parilty bit must be single.
> At the module end build a UART-RS232 connection using MAX 232 IC.
> Now connect the module to COM port through the UART.
> open the hyperterminal connection
> Turn on the module.
> type the AT commands.
> If nothing appears on the screen give (ATE1<CR>) echo command to the module.
> Now for every command the module responds by echoing the commands received from the hyperterminal and by giving the response code.

Added after 4 minutes:

Datasheet

Google
AdSense
Google Adsense

06 Apr 2005 13:21 Ads

Sorry, but you need login in to view this attachment

Richyroolahs

Joined: 30 Jul 2009
Posts: 1
Location: UK

30 Jul 2009 21:54 a1018 at commands

Hello. I am trying to interface an Ericsson T28s with an Arduino Nano via the serial connection on both pieces of hardware. I have the Tx and RX from the phone connected directly to the Rx and Tx of the Arduino (Rx to Tx and vice versa), and the ground of the phone is directly connected to the ground on the Arduino.
This, however seems to be wrong, as the screen on the Ericsson goes flickery when connected to the Arduino and seems to get progressively darker over a period of around four or five seconds, after which point I wrench the wires out of my breadboard through fear of frying the poor little phone.

I have a feeling that the voltage level of TTL (which is what comes out of the Arduino) may be too high for the phone.

Could anybody suggest anything to me that may help?

Thanks so much,

Richard